Vehicle Details
I’ve owned this since 2017, and I am the second owner.
It’s been a journey to get it here but it’s time to move on. Would consider partially trading to Huracan, 720 or 488.
The turbos are insanely loud with the T51R mod, car gets a lot of attention here in Naples. Drives like a dream just very loud.
Miles 26k miles
2009 Nissan GT-R
JN1AR54F99M250352
Tuned by Nick Dixon
Engine Built by Tim Lynch
Transmission by Ben Linney
Turbo kit by ETS (brand new turbo kit, T51R mod)
(Brand New Engine) rebuilt 2023
Body-
Full 2017 Upgrade including bumpers side skirts headlights and taillights
Ams drag radials new race masters 17/18
Custom orange pearl paint (everything is painted)
Boost Logic Parachute
Interior
Full alcantara interior (seats dash everything)
Digital alcantara steering wheel
Roll cage
Tesla Screen Entertainment System (SBD, I have original if you are not a fan)
-FUEL SYSTEM:
Injector Dynamics ID 1700x and 2800cc
Boost Logic 12 injector manifold
AMS fuel rails
Fore triple pump- 3 525 Walbaro
Fore fuel pump controller
Three port Mac boost solenoid
Got boost flex fuel sensor(.05-4.5 scaling)
Tial wastegates
Intakes and Downpipes 4”
Mid pipe 4”
Fabworx 4” exhaust system
Aem fuel pressure and coolant pressure sensor
Speed density kit
Motec 5 Bar map Sensor
ETS Pro 2100 with T51R Mod
AMS RaceCooler
Tial blow off valves
K&N air filters
Mishimoto Radiator (must for Florida)
Lynch Mob Racing stage 3.5
Build:
Disassemble & inspect long block for build
Disassemble & inspect cylinder heads for build. Check & reuse spring & retainer kit. Lap in existing stainless valves. Install new GSC S3 cams and set correct lash. Install new seals.
Fire ring & jack bolt mod. (Parts & service)
CNC block work to install 12mm main studs & 8 center head stud mod.
Wash all parts for assembly. Includes cleaning of old silicone off of pan & covers.
Balance Bryant crank for new rods & pistons
Check pin fit of new rods & pistons
Assemble LMR spec Billet crank long block
Nissan block assembly
Nissan Bank 1 cylinder head
Nissan Bank 2 cylinder head
Spark plug tubes
Bryant 3.8 billet crank
Manley 300M VR38 rod set
Wiseco LMR spec 10:1 Billet pistons with .250 Trend pins. Boost Logic 12mm main stud kit
Boost Logic 8 center long head studs
Nissan master gasket kit
Nissan Buckets
Nissan oil pump pick up tube
GSC S3 cams (4)
Narrowed Nissan rod & main bearings. (for Bryant crank) Nissan timing component set. Includes 3 chains, 3 tensioners, & 2 VVT gears.
Dodson front cover oil passage gasket kit
LMR spec extra capacity billet oil pan
Powder coating of covers spatter black
Nissan replaced front cover hardware
Linney New forged Gearset- Trans build by
DSS Axles Pro Level
Sauce shop
Billet front diff
ATR Bell housing
Linney 20 plate carbon clutch
Dodson Billet ETS
Dodson Motorsport reinforced gearbox
Driveshaft Shop drives
Driveshaft Shop reinforced gear reducers
Quaife front gear reducer lock
Front gear reducer lock
Dodson Motorsport gearbox gaskets
Dodson Motorsport seals
Custom-built circlips
Price: USD 134,990.00
Leave a Reply